Takip et
Dr. Shailendra Kumar
Dr. Shailendra Kumar
Professor, Department of Mechanical Engineering,S. V. National Institute of Technology, Surat, India
med.svnit.ac.in üzerinde doğrulanmış e-posta adresine sahip - Ana Sayfa
Başlık
Alıntı yapanlar
Alıntı yapanlar
Yıl
Fused deposition modelling: A review
S Vyavahare, S Teraiya, D Panghal, S Kumar
Rapid Prototyping Journal, 2020
3262020
Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet
A Dhanawade, S Kumar
Journal of Composite Materials 51 (24), 3373-3390, 2017
1162017
Experimental study of surface roughness, dimensional accuracy and time of fabrication of parts produced by fused deposition modelling
S Vyavahare, S Kumar, D Panghal
Rapid Prototyping Journal 26 (9), 1535-1554, 2020
872020
A knowledge based system for automated design of deep drawing die for axisymmetric parts
V Naranje, S Kumar
Expert Systems with Applications 41 (4), 1419–1431, 2014
792014
A short note on an intelligent system for selection of materials for progressive die components
S Kumar, R Singh
Journal of Materials Processing Technology 182 (1-3), 456-461, 2007
612007
An automated design system for progressive die
S Kumar, R Singh
Expert Systems with Applications 38 (4), 4482-4489, 2011
582011
A low cost knowledge base system framework for progressive die design
S Kumar, R Singh
Journal of Materials Processing Technology 153, 958-964, 2004
552004
Abrasive water jet machining of carbon epoxy composite
A Dhanawade, S Kumar, RV Kalmekar
Defence Science Journal 66 (5), 522, 2016
502016
Applications of artificial neural network to sheet metal work-A Review
S Kashid, S Kumar
American Journal of intelligent systems 2 (7), 168-176, 2012
442012
Automation of strip-layout design for sheet metal work on progressive die
S Kumar, R Singh
Journal of Materials Processing Technology 195 (1-3), 2008
422008
CCKBS: A component check knowledge-based system for assessing manufacturability of sheet metal parts
S Kumar, R Singh, GS Sekhon
Journal of Materials Processing Technology 172 (1), 64-69, 2006
402006
Study on carbon epoxy composite surfaces machined by abrasive water jet machining
A Dhanawade, S Kumar
Journal of Composite Materials 53 (20), 2909-2924, 2019
372019
Numerical and experimental investigation of FDM fabricated re-entrant auxetic structures of ABS and PLA materials under compressive loading
S Vyavahare, S Kumar
Rapid Prototyping Journal 27 (2), 223-244, 2021
362021
An experimental investigation on cutting performance of abrasive water jet machining of austenite steel (AISI 316L)
P Trivedi, A Dhanawade, S Kumar
Advances in Materials and Processing Technologies 1 (3-4), 263-274, 2015
362015
Re‐entrant auxetic structures fabricated by fused deposition modeling: An experimental study of influence of process parameters under compressive loading
S Vyavahare, S Kumar
Polymer Engineering & Science 60 (12), 3183-3196, 2020
342020
An intelligent system for automatic modeling of progressive die
S Kumar, R Singh
Journal of Materials Processing Technology 194 (1-3), 176-183, 2007
312007
Experimental study on abrasive water jet machining of carbon epoxy composite
A Dhanawade, P Kumar, S Kumar
Advances in Materials and Processing Technologies 6 (1), 40-53, 2020
282020
A knowledge based system for selection of components of deep drawing die
V Naranje, S Kumar
American Journal of Intelligent Systems 2 (2), 1-11, 2012
272012
An intelligent system for selection of die-set of metal stamping press tool
S Kumar, R Singh
Journal of Materials Processing Technology 165, 1395–1401, 2005
262005
Laser cutting of AISI 304 material: an experimental investigation on surface roughness
A Jadhav, S Kumar
Advances in Materials and Processing Technologies 5 (3), 429-437, 2019
222019
Sistem, işlemi şu anda gerçekleştiremiyor. Daha sonra yeniden deneyin.
Makaleler 1–20